Check six things before you accept any helmet test report: the standard and its edition year, the exact model and size the report covers, the conditioning applied before impact, the laboratory's identity and accreditation, the recorded peak values rather than the pass verdict, and whether a declaration of conformity exists beside it. A report that fails any one of those checks does not prove your helmet is compliant, even when every page says PASS.
This matters because the paperwork is usually the only part of a compliance claim a buyer can inspect. You cannot see the impact rig from your office in Rotterdam or Chicago. You can read the document.
A test report is not a certificate
A test report records what a laboratory did to a sample on a given date. A certificate, where one exists, states that a conformity assessment was completed. A declaration of conformity is the manufacturer's own legal statement that the product meets a named standard. Buyers routinely ask for "the certificate" and accept a test report in its place, which is fine only if the report actually covers the product being shipped.
For helmets sold in the EU, the CE marking is not issued by the factory on its own authority; the route runs through an EU type-examination for the product category, and the supporting documentation should name the model and the standard. Confirm the required conformity module against the current regulation and the actual test report, not against a supplier's summary of it.
The six fields that decide whether it covers your product
| Field | What to look for | How the claim breaks |
|---|---|---|
| Standard and edition | EN 1078:2012+A1:2012, EN 12492:2012, EN 1077:2007, 16 CFR 1203, GB 2811-2019 | A report to a withdrawn edition, or a standard for a different sport |
| Model and size | Your model code and each size tested, listed explicitly | A report for one size presented as cover for S to XL |
| Conditioning | Hot, cold, wet and ageing sequences recorded | Impact results with no conditioning record at all |
| Laboratory | Named lab, report number, accreditation scope | An unbranded PDF with a logo and no report number |
| Measured values | Peak acceleration per impact point, not just PASS | All results at 240 g against a 250 g limit means no margin |
| Date and sample link | Issue date after the tooling was finalised | A 2019 report for a shell moulded in 2024 |
The edition year is part of the standard
EN 1078 is cited as EN 1078:2012+A1:2012, and that edition is what a European buyer is relying on. A report that cites an earlier printing, or that names a standard without an edition at all, leaves you unable to show what was tested. The same applies across categories: EN 12492:2012 for climbing and work-at-height shells, EN 1077:2007 for ski and snowboard, 16 CFR 1203 for the US bicycle market, GB 2811-2019 for the Chinese industrial helmet standard.
Different standards are not interchangeable. A BT-23 climbing shell tested to EN 12492 and GB 2811-2019 tells you nothing about whether an M-4 cycling shell at 250 g passes EN 1078, because the impact points, the anvil geometry and the retention tests differ.
Size coverage is the most common gap
Laboratories test a sample, and a sample is one size. A report covering size L does not automatically extend to M or XL, and the arithmetic of scaling a shell across a size run is not something a report can imply. If you are buying S, M and L, ask which sizes were submitted. Where a factory tests a representative size and declares the rest of the run by technical justification, that justification should be written down and referenced in the report, not asserted in an email.
Conditioning is where cheap reports hide
Helmet standards do not test a helmet at room temperature only. EN 1078 requires impact performance after conditioning, including exposure to elevated temperature around +50 °C, low temperature around -20 °C, and water immersion, because an EPS liner and a polycarbonate shell behave differently when hot, cold and wet. Check the exact conditioning set required by the edition named on the report.
A report with no conditioning section is not a lenient report. It is a report to a different test programme.
Ask for the numbers, not the verdict
The EN 1078 impact test drops a helmeted headform 1.5 m onto a flat anvil, roughly 5.42 m/s at impact, and caps peak acceleration at 250 g. A result of 248 g passes. A result of 130 g passes with margin. That difference tells you how much room the design has when a production shell comes in slightly heavier, or when a customer asks for a thicker graphic film.
Buyers who ask for the measured values learn something about the supplier. Buyers who accept "PASS" learn nothing except that the sample survived one day in a lab.
The laboratory and its scope
The report should carry the laboratory's name, a traceable report number, the test dates and the accreditation under which the work was done. SGS, TÜV, Intertek and the larger Chinese labs are all credible, and CNAS accreditation covers a defined scope that a buyer can check. For the US bicycle market, the 16 CFR 1203 testing has to come from a CPSC-accepted laboratory; a European report is not a substitute, and neither is a US report for an EN 1078 claim.
What should sit beside the report
Three documents travel with a compliant helmet, and each does different work.
- The declaration of conformity, naming the manufacturer, the model and the standard.
- The permanent label, carrying the standard reference, the model identification, the size and the manufacturer or importer, in the form the destination market accepts.
- The user information, with fitting, adjustment and replacement guidance, in the language of the market.
If the label text and the report disagree on the standard or the model code, the shipment has a problem regardless of how the helmet performs. Confirm every line of label copy against the report before artwork is released.
Red flags that appear in the documents themselves
- A report number that cannot be found in the issuing laboratory's system.
- A "certificate of compliance" issued by a consultancy rather than a testing body.
- One impact point recorded where the standard requires several.
- A test date that precedes the tooling sign-off, meaning the mould that was tested is not the mould in production.
- Sizes listed as "all" or "series" with no tested size identified.
- Photographs of a sample that is visibly a different colourway or vent pattern from the product being offered.
None of these is proof of fraud. All of them are reasons to ask a question before you commit a season.
The email to send a factory
Five requests cover most of it, and a factory that has the paperwork will answer within a day.
- The full test report, with report number and laboratory, for the model and each size quoted.
- The conditioning record and the peak acceleration values per impact point.
- The declaration of conformity for the model, naming the standard and edition.
- The label artwork and its position on the shell, checked against the report.
- The date the current shell tooling was finalised, so the report can be tied to the mould in production.
Why a factory will sometimes tell you to read the report
Publishing a certificate number on a website is easy and proves little, because a number does not say which model, which size or which edition it covers. A factory that answers a compliance question by pointing you to the document, with the model and size named, is doing the more useful thing.
Programmes from this factory ship out of Dongguan through Shenzhen, at a 500-piece MOQ and a 30 to 45 day production window. If you are evaluating a specific model, sample it and take the paperwork with it, so the shell in your hand and the report in your inbox are the same object. Where a figure matters to your market, confirm it against the actual test report rather than against a summary. WhatsApp +86 173-2675-4394 or jack@lanbomeni.com.